2 Channel RGBW LED Dimmer, DIN Rail Mount

Model: DIN-2LEDPWM8

Two independently powered and controlled LED dimming outputs
Each output controls one RGBW LED or LED strip or four independent LEDs or LED strips
PWM (Pulse Width Modulation) dimming technology for flicker-free dimming
Controls 12–24VDC LEDs and LED strips
100 W maximum power at 24VDC at 5A

View Manufacturers Website

More Product Information Below

Compare

Project List

Product Info

Tech Specs

Related Products

Documents

The Crestron® DIN-2LEDPWM8 is a two channel RGBW dimmer that uses PWM (pulse width modulation) frequency for flicker-free performance. A Cresnet® control port is provided for integration with a Crestron control system.

DIN Rail Mounting
The DIN-2LEDPWM8 is designed to snap onto a standard DIN rail for installation in a wall mount enclosure (Crestron DIN-EN series or similar, sold separately) or on a wall panel. DIN rail mounting affords a very space-efficient, cost-effective, and modular solution for configuring complete automation systems. Wiring connections are made using screw terminals positioned along the top and bottom, clearly accessible from the front for easy installation and servicing. When installed in an enclosure utilizing 45 mm cutouts, the DIN-2LEDPWM8's front panel stays accessible while the connections are concealed.

Cresnet® Communications
The DIN-2LEDPWM8 communicates with a Crestron control system via the Cresnet control network. A pair of Cresnet ports are provided on the DIN-2LEDPWM8 to allow easy daisy-chaining of several Crestron DIN rail devices.

Override Input
Override inputs are provided to allow an external contact closure to momentarily override the control system program and set each channel output to its preset override level. Levels can be adjusted and saved locally from the front panel or remotely via software.

Two independently powered and controlled LED dimming outputs
Each output controls one RGBW LED or LED strip or four independent LEDs or LED strips
PWM (Pulse Width Modulation) dimming technology for flicker-free dimming
Controls 12–24VDC LEDs and LED strips
100 W maximum power at 24VDC at 5A
60 W maximum power at 12VDC at 5A
Two Cresnet® control ports for integration with a Crestron® control system and daisy-chain wiring
Two override inputs accept override signal from an emergency system to raise light levels to 100% (or desired level)
Front panel interface for control, setup, and device status
6U 35 mm DIN rail mountable

Spec Sheet available - Yes

Certifications: CE, ETL, FCC, CAN ICES, UL
Depth: 59.44 mm
Height: 107.70 mm
Width: 107.70 mm
Product Weight: 0.18 kg
COMMUNICATIONS:
•Cresnet: Cresnet slave mode
Modules:
•Dimmed Channels: 2 RGBW
•Maximum per Channel: 5A max per individual RGBW output channel, 5A max per RGBW output group
•Module Total: 10A max
•Load Types: 12–24VDC PWM controlled anode RGBW or single color LEDs and LED strips
•Dimming Range: 0–100%
•PWM Frequency: 301Hz (default)
•Configurable: 120–1,200Hz
•Dimming Curve: Linear and logarithmic
Power Requirements:
•IN 1: 12–24VDC, 5A max (60–100W max) Class 2; Powerpass-through to OUTPUT-1
•IN 2: 12–24VDC, 5A max (60–100W max) Class 2;Power pass-through to OUTPUT-2
Power:
•IN 1 (+, -):
•(1) set of (2) captive screw terminals;Power input and power pass-through to OUTPUT-1;Use a 12–24VDC, 5A max (60–100W max) Class 2 power supply (not supplied);Ensure proper polarity;Wire size: 18–12AWG
•IN 2 (+, -):
•(1) set of (2) captive screw terminals;Power input and power pass-through to OUTPUT-2;Use a 12–24VDC, 5A max (60–100 W max) Class 2 power supply (not supplied);Ensure proper polarity; Wire size: 18–12AWG
•OUTPUT-1 (R +, R 1, G +, G 2, B +, B 3, W +, W 4):
•(1) set of (8) captive screw terminals;R +, G +, B +, and W + terminals are pass-through power from IN 1 +;R 1, G 2, B 3, and W 4 terminals are PWM dimming control for the R, G, B, and W channels;Wiring from OUTPUT-1 must remain separate from OUTPUT-2;Accepts 18–14 AWG wires;Maximum wire length: 100 ft (30 m)
•OUTPUT-2 (R +, R 5, G +, G 6, B +, B 7, W +, W 8):
•(1) set of (8) captive screw terminals;R +, G +, B +, and W + terminals are pass-through power from IN 2 +;R 5, G 6, B 7, and W 8 terminals are PWM dimming control for the R, G, B, and W channels;Wiring from OUTPUT-2 must remain separate from OUTPUT-1;Accepts 18–14 AWG wires; Maximum wire length: 100 ft (30 m)
•NET:
•(2) 4pin 3.5 mm detachable terminal blocks, paralleled;Cresnet slave port;24VDC power input (power must be supplied by a DIN-PWS60 power supply (sold separately))
•OVERRIDE:
•(2) 2-pin 3.5mm detachable terminal blocks, paralleled;Sensing input for external low-voltage contact closure;Activates override mode when a closure is present;Minimum Closure Rating: 10mA (per module) at 24V
Controls:
•R, G, B, W: (4) miniature pushbuttons (1) per R, G, B, W channel;Press to toggle the channel on and off;Press and hold to dim the channel up and down
•SETUP: (1) recessed miniature pushbutton;Press to acknowledge Touch-Settable ID (TSID) mode
•RESET: (1) Recessed miniature pushbutton;Press to restart the DIN-2LEDPWM8
Indicators:
•R, G, B, W: (4) Red LEDs (1) per R, G, B, W channel; LED lights to indicate that the channel is on;All LEDs light when the DIN-2LEDPWM8 is in override mode
•SETUP: (1) Red LED; Flashes to indicate that the DIN-2LEDPWM8 is in Touch-Settable ID (TSID) mode
•OVR: (1) Red LED;Lights to indicate that the DIN-2LEDPWM8 is in Override mode;The R, G, B, and W LEDs also light to indicate that the channel is on
•PWR: (1) Green LED;Lights to indicate that DC power is supplied to the NET port
•NET(1): Amber LED;Flashes to indicate communication on the Cresnet network
Environmental:
•Temperature: 32° to 104°F (0° to 40°C)
•Humidity: 10% to 90% RH (noncondensing)
•Heat Dissipation: 6.8 BTU/Hr
Construction:
•Housing: Plastic, light gray polycarbonate housing with polycarbonate label overlay, UL94 V-0 rated
•Mounting: 35mm DIN EN 60715 rail mount, DIN 43880 form factor for enclosures with 45mm front panel cutout, occupies 6 DIN module spaces (108mm)

CLT-2DIMFLV8 - Terminal Block for CLX-2DIMFLV8

CLT-2DIMFLV8-277 - Terminal Block for CLX-2DIMFLV8-277

CLTI-2DIMFLV8 - Terminal Block for CLXI-2DIMFLV8

CLX-1DIMU4-HP - 4-channel 1-feed Universal Dimmer Module, High Power, 120V

CLX-2DIM8 - 8-channel 120V Dimmer Module, 2 Feeds

CLX-2DIMU8 - 8-channel Universal Dimmer Module, 2 Feeds

CLX-2DIMU8-277 - 8-channel 277V Universal Dimmer Module, 2 Feeds

CLXI-2DIM2 - 2 Channel Dimmer Module, 2 Feeds - International Version, 230V

CLXI-2DIM8 - 8 Channel Dimmer Module, 2 Feeds - International Version, 230V

DIN-1DIM4 - DIN Rail Dimmer, 1 feed, 4 channels

DIN-1DIMU4 - DIN Rail Universal Dimmer, 1 feed, 4 channels

DIN-4DIMFLV4 - DIN Rail 0-10V Fluorescent Dimmer, 4 feeds, 4 channel

GL-CAEN-2DIM8 KIT - 8-channel 120V Dimmer Module with Terminal Block, 2 Feeds

GL-CAEN-2DIMFLV8 KIT - 8-channel 120V Dimmer Module with Terminal Block

ss_DIN-2LEDPWM8.pdf 7019956 kb - Data Sheet

Project List

mg_qs_din-2ledpwm8.pdf 1167978 kb - Instructions

Project List

Find a Dealer