Lighting Control Systems : Dimmers & Dimmer Systems : Crestron Electronics, Inc. - ZUMLINK-JBOX-16A-LV

Zum Wired J-Box Load Controller, 0-10V Dimmer, 16A, 100-277V with Link Communication

Model: ZUMLINK-JBOX-16A-LV

Zum® wired junction box-mounted lighting load dimmer
Dimming control of 0-10V LED drivers or 4-wire fluorescent ballasts
Integration with Zum keypads, occupancy sensors, vacancy sensors, and daylight sensors (sold separately)
Supports in-room device daisy chaining
Integrated contact closure input

View Manufacturers Website

More Product Information Below

Compare

Project List

Product Info

Tech Specs

Documents

The Crestron Zum® Wired ZUMLINK-JBOX-16A-LV provides 0-10 V dimming for drivers and ballasts. The device can be wired to other in-room Zum devices to provide load control. Energy-saving options are available to enable daylighting, occupancy or vacancy sensing, and centralized monitoring and management.

Zum Link Wired Technology

Zum Link technology allows for in-room lighting control through compatible keypads and sensors. Two RJ-45 ports on the device allow for connection to a Zum Net device and for in-room device daisy-chaining. Similar to the Zum Wireless system, Zum Link devices work together in a local ecosystem to provide customized solutions as needed.

Easy Installation

For flexibility and ease-of-use, Zum load controllers are installed in a room with Zum keypads, occupancy or vacancy sensors, and/or a daylight sensor for complete commercial lighting control. Finish the installation by quickly commissioning the room through the Zum app.

Override Contact Closure Input

An integrated contact closure input or relay output on the ZUMLINK-JBOX-16A-LV provides the means to place all connected Zum Net and Zum Link devices into Emergency Override mode.

Zum® wired junction box-mounted lighting load dimmer
Dimming control of 0-10V LED drivers or 4-wire fluorescent ballasts
Integration with Zum keypads, occupancy sensors, vacancy sensors, and daylight sensors (sold separately)
Supports in-room device daisy chaining
Integrated contact closure input
Flying lead wiring connections
Knockout mount to a standard 4 in. square junction box

Spec Sheet available - Yes

Operating Temperature (Maximum): 40 C
Operating Temperature (Minimum): 0 C
Certifications: IC, FCC, cUL, UL
AC Voltage (Maximum): 277 Volts
AC Voltage (Minimum): 100 Volts
Current Draw: 16 Amps
Depth: 51.56 mm
Height: 122.68 mm
Width: 107.95 mm
Product Weight: 0.20 kg
Load Control:
•Dim Load Types: 0-10V LED drivers or electronic ballasts (4-wire)
•Switch Load Types: LED, electronic ballasts, incandescent, magnetic low-voltage, electronic lowvoltage,neon/cold cathode, high-intensity discharge, small motor loads
•Dim Control Output: 0-10VDC, 60mA maximum sink or source
•Short Circuit : Protection 40A non-replaceable fuse
Wired Communications:
•ZUMLINK (ROOM): (2) RJ-45 ports; In-room Zum Link device daisy-chaining; 85mA power available for Zum Link devices, including ZUMLINK-KP keypads
•24V, OCC, GND: Occupancy sensor input; 85mA available output current; Spring clamp connector
•24V, PHO, GND: Photo sensor input; Spring clamp connector
•OVR, GND: Override control input; Spring clamp connector
Controls and Indicators:
•TEST: (1) Pushbutton and (1) green LED; Push to toggle the switched load output on and off; Press and hold to cycle the dimming level up and down; LED indicates that the load is turned on; LED lights and flashes during room setup and factory reset
•ZUMLINK Status: (1) bi-color green/red LED; LED lights green in normal operation; LED lights red when a fault is detected
Connections:
•Hot: (1) 14 AWG Class 1 flying lead; Black, line power input
•Neutral: (1) 14 AWG Class 1 flying lead; White, neutral
•Red: (1) 14 AWG Class 1 flying lead, red, AC output
•Purple: (1) 18 AWG Class 1 flying lead, purple, 0-10VDC dimming control output, positive
•Gray: (1) 18 AWG Class 1 flying lead, gray, 0-10VDC dimming control output, negative
Humidity: 10% to 90% RH (noncondensing)
Construction:
•Housing: Plastic, white, UL 94 5VA flame rated
•Mounting: Mounts to the side of a 4 in. square junction box via a 1/2 in. conduit knockout; Meets the requirements of UL 2043 for installation in an environmental air-handling (plenum) space

Load Controller 2517685 kb - Data Sheet

Project List

mg_qs_zumlink-jbox.pdf 2334866 kb - Instructions

Project List

Find a Dealer