DisplayNet USB + Dante SDVoE Transmitter

Series: DisplayNet DN-200

Model: DN-225UD-TX

Utilizes SDVoE Technology to distribute AV signals with off-the-shelf 10GbE network switches
Supports HDMI 4K /60p signals with resolutions up to 4K /60p with 8-bit color (4:4:4) and 4K /60p with 10-bit or 12-bit color (4:2:2 or 4:2:0)
Includes scaling in the Receiver to enable Fast Switching
Vastly superior to conventional Video-over-IP products by providing: zero frame latency, zero compression, zero image artifacts
Supports HDMI, HDCP, Embedded Audio, Analog Stereo Audio, Downmixed Audio, Dante Digital Audio, High Speed USB 2.0 (480 Mbps.), Bidirectional IR, RS-232 and 1GbE over 10GbE link

More Product Information Below

Compare

Project List

Product Info

Tech Specs

Related Products

Documents

The DN-200 Series is the flagship product of the DisplayNet AV-over-IP product line. It leverages the latest SDVoE technology to distribute uncompressed AV signals with resolutions of up to 4K /60p (4:4:4) over a 10GbE Ethernet network. The DN-200 Series offers support for HDMI 4K /60p with up to 12-bit color, HDCP 2.2, DisplayPort 1.2, as well as High-Speed USB 2.0 with virtual hub support. A high-performance scaler in both the Transmitter (Tx) and Receiver (Rx) units enables very Fast Switching, Advanced MultiViewer, and Advanced Video Wall processing. The TX unit accepts multiple source signals including HDMI (with embedded audio and HDCP), DisplayPort, analog stereo audio, bidirectional IR, RS-232, and 1GbE Ethernet. These input signals are packetized into a single 10GbE link and are distributed to destinations using an off-the-shelf 10GbE network switch. The DN-200 Series supports twisted pair (CAT6a or CAT7) media up to 328 ft. (100 meters), as well as Fiber Optic media using an industry standard SFP+ module supporting extension distances up to 30 KM (18 miles). The 10GbE switch provides a highly efficient and reliable means of distributing AV signals from many sources to an array of Rx units, which convert the packetized 10GbE data to AV output signals at the destination in real time without introducing frame latency or any loss of image quality. The DN-200 Series distributes video with resolutions up to 4K /60p with 8-bit color (4:4:4) and 4K /60p with 10-bit or 12-bit color (4:2:2 or 4:2:0) without image artifacts and without frame latency. When the video signal exceeds the bandwidth limits of 10GbE, very light compression (maximum ratio of about 1.4:1) is used. Video signals may be routed in Point-to-Point, Matrix Switching, Video Wall, and MultiViewer modes all in the same system. For optimum flexibility, each signal layer (Video, Embedded Audio, Downmixed Audio, Analog Audio, IR, RS-232, and 1GbE) can each be routed completely independently from one another. Advanced audio features are supported, including: networked audio, audio embedding, de-embedding and downmixing. The DN-225UD-TX supports Dante® digital audio, which can send Analog Stereo Audio, as well as de-embedded or downmixed HDMI audio to any Dante device using the 1GbE LAN Port. DN-200 Series transmitter and receiver units are controlled by a DisplayNet Server® (DNS-20), which includes a powerful DisplayNet API Engine and DisplayNet Manager® web browser-based software that enables the system to be managed using any third-party controller using simple Telnet commands.

Utilizes SDVoE Technology to distribute AV signals with off-the-shelf 10GbE network switches
Supports HDMI 4K /60p signals with resolutions up to 4K /60p with 8-bit color (4:4:4) and 4K /60p with 10-bit or 12-bit color (4:2:2 or 4:2:0)
Includes scaling in the Receiver to enable Fast Switching
Vastly superior to conventional Video-over-IP products by providing: zero frame latency, zero compression, zero image artifacts
Supports HDMI, HDCP, Embedded Audio, Analog Stereo Audio, Downmixed Audio, Dante Digital Audio, High Speed USB 2.0 (480 Mbps.), Bidirectional IR, RS-232 and 1GbE over 10GbE link
Fully Routable, Independent Switching Layers for all signal types: Video, Embedded Audio, Analog Audio, Downmixed Audio, Dante Digital Audio, USB, IR, RS-232
Supports Audio Embedding, De-embedding and Downmixing
Enables custom video wall configurations with optimized bezel correction and asymmetric wall support, for wall arrays of up to 8x8
Supports fully customized MultiView layouts and configurations with a simple drag-and-drop interface
Powerful built-in script editor enables creation of Scripts and Presets, greatly reducing the time needed for system set-up and configuration
Supports advanced EDID Management, including the display of detailed EDID information and an integrated library for EDID storage and retrieval
Unconstrained scalability – Size of I/O array only limited by number of 10GbE switch ports
Support for both copper and fiber 10GbE network connectivity within the same unit
Maximum range up to 100 meters (328 ft.) using a single CAT6a or CAT7 cable
Maximum range up to 30 KM (18 miles) using single-mode SFP+ Module
DisplayNet Server and DisplayNet Manager enable deep integration into new or existing AV systems

Dante Enabled - Yes
Rackmountable - Yes
SDVoE Enabled - Yes
Warranty - Yes

Depth: 145.40 mm
Height: 35 mm
Width: 210 mm
Product Weight: 1.45 kg
Colour: Jet Black
Warranty (Length/Type): Limited Warranty: 3 Years Parts and Labor
Supported AV Signals:
Video – HDMI (4K /60p), DisplayPort 1.2, DVI 1.0 and HDCP 2.2
HDCP – Compliant with HDCP 2.2
Embedded Audio – Supports pass-through of embedded HDMI audio including up to 8 channels of LPCM or HBR audio formats such as: Dolby Digital TrueHD, and DTS-HD Master Audio
De-Embedded Audio – Supports independent routing of de-embedded HDMI audio: Up to 8 channels of LPCM digital audio with up to 24-bit depth and 192 kHz sampling rate
Downmixed Audio – Supports independent routing of 2-channel de-embedded / down-mixed HDMI audio. Requires input signal to be PCM audio format
External Audio – Supports independent routing of analog stereo audio stream with up to 24-bit depth and a fixed 48 kHz sampling rate
Digital Audio-over-IP – 2-Channel Dante digital audio output via the 1GbE Port. Supported inputs: Analog Stereo Audio Input; HDMI Downmixed Audio (downmixed to 2 channels); HDMI Audio – (Left and Right channels only) (NOTE: The HDMI input only supports PCM Audio. 1GbE connectivity for non-Dante usage is not supported.)
USB Control – Supports switchable High Speed USB 2.0 (480 Mbps.) extension with virtual hub functionality, with up to 4 RX units per TX
IR Control – Supports bidirectional IR switching
RS-232 Control – Supports bidirectional RS-232 switching via UART interface with up to 115,200 baud
Connections / Indicators:
10GbE Port (1)(2) - 1ea. shielded RJ45 connector with LED indicators, and 1ea. Fiber Optic SFP+ slot (populated with SFP+ module sold separately)
HDMI Input / HDMI Output - 1ea. 19-pin Female HDMI connector
DisplayPort Input - 1ea. 20-pin Female DP connector (Input on TX)
Analog Stereo Audio - 1ea. 3.5mm Stereo-Mini Jack (Input / Output on TX and Output on RX)
USB 2.0 (2) - TX Units: 1ea. USB 2.0 Type B connector; RX Units: 2ea. USB 2.0 Type A connector
RS-232 - 1ea. 4-pin, 3.5mm pitch, Phoenix connector
IR Control - 1ea. IR IN: 3.5mm Stereo Mini-Jack; 1ea. IR OUT: 3.5mm Mini-Jack
DC Power - 1ea. 5.5 mm / 2.0 mm female screw-locking connector
Diagnostic LEDs - TX Link, RX Link, Video, USB, Power
Hardware Reset - 1ea. Push-button to restore factory default values
Performance:
Supported Resolutions (2) – Up to 4K /60p with 8-bit color (4:4:4); Up to 4K /60p with 10-bit or 12-bit color (4:2:2 or 4:2:0)
Maximum Pixel Clock Frequency – Supports pixel clock rates up to 600 MHz
Maximum Video Bit Rate – Supports digital signal bit rates up to 6.0 Gbps./color, 18.0 Gbps. Total
Switching Layers – Independent switching layers for all connected Video, Embedded Audio, Analog Audio, HDMI and Downmixed Audio, RS-232 and IR
Video Signal Latency (3) –
Genlock: ≤30 µn;sec. (uncompressed), ≤ 120 µn; sec. (compressed) (3)
Genlock Scaler: 3.0 msec.
Fast Switch: 1-2 Frames
Video Wall: 1-2 Frames
MultiViewer: 1-2 Frames
Supported I/O Switching Array – Size of I/O array is only limited by the size (number of ports) of the 10GbE network switch
Recommended CAT Cable – CAT-6A S/FTP (500 MHz) AWG 23, or CAT-7 (Europe); Compliant with TIA/EIA-568B termination standard
Maximum Cable Distance – up to 328 ft. (100 meters) using CAT-6A S/FTP (500 MHz) AWG 23 cable
HDMI Input Cable Equalization – Supports DVIGear's HR™ Series HDMI with cable lengths up to 10 meters at 4K /60p resolution
Operational Modes:
Matrix Switching Mode – Fully non-blocking cross-point routing of nearly any size I/O array – only limited by size of 10GbE switch(4)
Video Wall Mode – Supports Advanced Video Wall displays using integrated scaling engine in the RX. Supports asymmetric walls with crop, scale, and letterbox modes(4)
MultiViewer Mode – Supports customizable MultiViewer displays with up to 32x sources using integrated scaling engine in the TX(4)
Point-to-Point Mode – Supports Point-to-Point Extension up to 328 ft. / 100 meters (CAT6A) or 30 KM (18 miles) (single-mode fiber) using recommended cables and SFP+ modules(4)
Power:
Typical Power Consumption – DN-225U-TX: 17.55 watts / DN-225U-RX: 18.24 watts
External AC Power Adapter – Input: 100-240VAC, 50-60Hz / Output: +12VDC @ 3A
DC Power Output – 1.0 watt – 5VDC @ 200 ma on HDMI pin 18 on DN-225-RX
Environmental:
Operating Temp. (Environment) – +32° to +104° F (0° to +40° C)
Typical Case Temperature – Tx Unit: 98.6° F (37° C) Rx Unit: 105.8° F (41° C)
Storage Temp. (Environment) – -4° to +158° F (-20° to +70° C)
Operating / Storage Humidity – 10% to 90% (non-condensing)
Regulatory Approvals:
TX / RX Units – FCC, CE, RoHS –
External AC Power Adapter – CE, UL, C-UL, CEC, GS, PSE, CCC, RoHS, WEEE, S, RCM, Class II
Accessories Included:
Included – 1x External AC Power Adapter (per unit)
2x Mounting Brackets with Screws (per unit)
1x 4-pin RS-232 Phoenix Connector (per unit)
1x IR Transmitter (per TX unit)
1x IR Receiver (per RX unit)
Optional Accessories:
DisplayNet Server (model DNS-20)
External AC Power Adapter with USA, Euro, UK, or Australia Plugs
Power Distribution Unit, 8x 12VDC (DVI-7520-PDU)
IR Transmitter (DVI-7360-IR-TX), IR Receiver (DVI-7360-IR-RX)
19" Rack Mount Kit (DN-100-RMK)
DVI-I Female to HDMI Male Adapter Cable (DVI-8511c)
Notes:
Note 1: The 10GbE port is designed to connect to compatible DVIGear products and 10GbE network switches only. Do not connect any device to the 10GbE port of this product unless you are sure it is compatible.
Note 2: Video signals will be transported uncompressed unless the bandwidth exceeds the limits of 10GbE.
Note: For video signals that exceed 10Gbps. of bandwidth, light compression is employed. For the maximum resolutions shown above, the DN-200 Series employs a compression ratio of about 1.4:1.
Note 3: DN-200 Series uses lightweight compression for some high bit rate formats (e.g. 4K /60p), which adds a few extra lines of latency. For Fast Switch, Video Wall, and MultiViewer modes, a maximum of 2 frames of latency translates to not more than 33.3 msec. @ 60Hz and not more than 67.7 msec @ 30Hz.
Note 4: A system may operate concurrently in Matrix Switching, Video Wall, and MultiViewer modes.
Note 5: The DisplayNet Server is required for the majority of system configurations.

DN-150-TX-Quad - DisplayNet Quad HDMI Input Module for NETGEAR M4300-96X

DN-225U-RX - DisplayNet SDVoE USB Receiver

DN-225U-TX - DisplayNet SDVoE USB Transmitter

DNS-20 - DisplayNet Server®

DisplayNet USB + Dante SDVoE Transmitter Technical Drawing 1505603 kb - Other

Project List

DisplayNet DN-225 Mounting Bracket Technical Drawing 899452 kb - Other

Project List

Suggested Products

Universal Matrix Switcher with USB-C Connectivity and Dante USB Audio Bridge

by Lightware

HDMI 4x4 Matrix Selector Switch 4K/60Hz HDR HDCP 2.2

by Vanco International

4K 18Gbps HDMI Video Matrix Switch, 16x16, 1RU

by Network Technologies Inc. (NTI)